odds and ends hen house

Just a show-and-tell, not a tutorial, since your scrap pile will differ from mine significantly. With the exception of hinges, hardware, and shingles from Bring and some chicken wire from the farm store, all materials were on-hand including leftover cedar siding and fence board scraps, sections of 2x4 and 2x2, chunks of 4x4 posts, and old bifold closet doors.

(This is a chicken house, yes, but our outside cat sleeps safely in there at night, protecting her from cars and fights.)

Enjoy!

The scrap pile was pulled out onto the lawn for planning the hen house.

Some pieces were cut to length for support structures.

With slats removed, bifold door braces make side supports.

The basic structure, made of 2x4 scrap, bifold door lumber, and 2x2 pieces.

The door, made of leftover cedar siding and 1x3 boards.

The first side gets covered in siding.

The "run", framed in, was ready to be covered with chicken wire.

The hen house was covered in cedar siding, then had the roof peak added.

Legs are made from 4x4 chunks leftover from a fencing project.

Inside, floor boards are made of scrap lumber, and a vent on the back wall is made of hardware cloth tucked between layers of siding. The space left in the floor is the entry/exit to the run.

Side view of the hen house attached to the run.

Hardware cloth is attached to the roof peaks for ventilation and a view.

Shutter slats are nailed in place to hide edges and cover the sharp ends of wire on the outside.

Roof decking is made of lengths of cedar fence boards.

Tar paper covers the roof decking. We've had this tar paper leftover from roofing and siding  projects on the shed and studio.

Asphalt shingles are pretty easy to come by at Bring in small quantities. I found just enough to cover the roof.

I used a partial tube of roofing tar to secure the shingles in addition to roofing nails. We had the tar leftover from installing a skylight in the shed earlier this summer.

The door handle and piano hinge came from Bring as well. The other hinges were removed from an old standing screen that had its lumber incorporated into this project.

A small shelf holds a cat food can up off the ground. The edge is made of shutter slats.

Finished! The chicken wire run is continued to the area underneath the hen house, allowing for extra space to move, and is held to the ground with tent stakes.

The door is latched with a hook & eye on each side. The run is attached to the hen house with hook & eye fasteners as well, which allows for easy cleaning.

Complete! One hen house made mostly of stuff we had on hand. This was an interesting challenge because the scrap pile had to be used creatively to make a solid and attractive structure. In the end, it lives up to expectations. I think any time I build from scrap I end up especially happy with the results, but this hen house is one of my favorites.

Thanks for following along as I innovated!

Linking up to:
My Repurposed Life

simple animal paw shoes for theater + halloween costumes

I made these shoes for the Cat in the Hat for our preschool's recent production, to match the costume I retrofitted (coming up in a future post). It's funny; I had let the other costume maker borrow my one and only costume shoe pattern and was scrambling to get some shoes made for a dress rehearsal, but this style actually ended up working better than the pattern I'd loaned her.

You'll remember that my computer died? As in DEAD dead. The hard drive and logic board both keeled over at the same time, which means I could only use my phone for internet searches, and my phone won't send anything to my printer. So while I remembered this Martha Stewart felt slippers pattern, I had to improvise and hand-draw rather than printing it. All's well that ends well; these turned out just right.

For the soles, I used two layers of this old rough-backed felt from the stacks of leftover fabric in the theater supplies at school. For the body, I used one layer of the stiff-backed felt and one layer of the hound's tooth flannel I'd used for the Cat's costume. The foot pads are cut from a scrap of red ostrich leather I bought awhile back at a thrift store, zig-zag appliqued into place before assembling the shoes.

To make your own, you can follow Martha's original instructions with the following changes:

1) Instead of a single layer of thick felt, I used one layer of thinner craft felt and one layer of woven fabric, serged together at the edges. Word to the wise: when using thinner felt, using mutiple layers is key. You'll get a lot of stretch and wear-through with single layers.

2) The appliques are used (in addition to the rough-bottomed felt) to make the shoes non-slip, and to add some durability. Highly recommended, whether for Halloween or for theater. In addition to making the shoes less slippery and more sturdy, the pads are an especially nice touch if, at any point, your character shows the bottoms of his or her feet to an audience. This happened in our play, and every time I could feel how much it added to the kids' experience.

3) The original pattern leaves the seams on the outside; I tucked mine inside.

4) As the cuffs are layered with woven fabric + felt, they don't have much stretch, so the wearer will have to spend a minute working them onto his or her feet. It actually makes them fit really securely, and for a seldom-used costume piece it's not too much of an inconvenience.

Like most things, you can adapt these pretty endlessly to a variety of costumes. Switch up the fabric, use faux fur, different color leather, etc.

More to come! Thanks for reading.

the cat in the hat mini hats

A couple of factors played into the lack of activity at the blog over the past couple of weeks. First, I was scrambling to finish up the last few costume projects before our preschool's all-parent production of The Cat in the Hat. A few late nights, some scavenging for materials, and a couple of re-dos later, and everything came together. It was a pretty amazing group of people who came together on the project.

Second, my computer died. Like, completely. I took it in with a blank white screen with only a gray apple in the middle, and when it came back to me a little over a week later, they'd replaced the hard drive and the logic board. Thankfully, luckily, magically, there was a week left on the AppleCare extended warranty the Mr. had the foresight to buy. A week later, and we'd have been paying out-of-pocket for the parts and repairs. And it would have cost about as much as I earned on Etsy this year. I feel really lucky.

Anyway, on to today's post.

Let's look at making some Cat in the Hat mini hat headbands!

You can use this idea for making any kind of mini top hat, really, just by changing the color of the stiffened felt and adding some embellishments. Here's what you need to know.

Materials for two hats:

1 12 x 18-inch piece of stiffened felt (also called Friendly Felt) in white or glittered white
2 9 x 12-inch pieces of regular red felt or glittered red felt
red and white thread
hot glue
2 red ribbon-covered headbands

For each hat, cut a piece of stiffened white felt that's 4 1/2 x 12 inches, and three red stripes that are approximately 1 x 12 inches. You'll also need a red circle that measures approximately 3-inches in diameter, and two stiffened white circles (not one red + one white, as photographed) measuring approximately 4 1/2 inches in diameter.

Arrange stripes as shown, then stitch in place using red thread.

Using the red circle as a guide, pin the striped felt into a tube that will use the red circle as a top. You can either pin it inside out to machine stitch and turn carefully right side out again, or you can pin right side out and hand stitch using a mattress or a slip stitch. Both ways will work.
 
After pressing that seam to make sure the tube retains its round shape, sew the red circle to the top using red thread to whip stitch it in place.

Center the hat's top on one of the white circles, then use red thread to whip stitch it in place.

Hot glue the hat to a headband, then cut slots on either end of the remaining white circle to accommodate the head band (as photographed).

Line the circle up with the underside of the hat and the headband, then hot glue in place. Make sure to use lots of glue on the headband, and a scant amount of glue on the white felt so that it doesn't leak through. Then whip stitch to the hat and you're done!

Use similar materials for Mad Hatter or steam punk style hats! Switch to black or brown felt and headbands, and add feathers, ribbons, and other embellishments. And then send me a link so I can see what you've made!

Thanks for reading!

p.s. you can make these photos larger by clicking on them for more detail!

happy birthday dr. seuss

Celebrating the 110th birthday of Theodore Seuss Geisel, Dr. Seuss, creator of the modern picture book, whose stories help lull my kid to sleep on a wave of rhyme.

Fish Puppet for The Cat in the Hat play at the preschool, made from corrugated cardboard (old box), felt, cotton broadcloth, polyester fiber fill, cotton canvas (old painters' drop cloth), latex and acrylic paint, thread, and hot glue.